- Manuals
- Brands
- MGC Manuals
- Control Panel
- RAXN-4000LCD
- Installation and wiring manual
Network remote annunciator panel
Hide thumbs
1
2
Table Of Contents 3
4
5
6
7
8
9
10
11
12
13
14
15
16
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Table of Contents
-
Introduction
-
Installation Instructions
-
Jumper Settings
-
DIP Switch Settings
-
Wiring Instructions
-
Cable Connections
-
Specifications
-
Battery Calculations
-
Warranty and Warning Information
Advertisem*nt
Quick Links
Download this manual
RAXN-4000LCD
Network Remote Annunciator Panel
Installation and Wiring Manual
MGC Network
Fire Control System
- System
Normal -
Feb 21, 2018
2:21 PM
ALARM
SUPV.
TROUBLE
MONITOR
QUEUE
QUEUE
QUEUE
QUEUE
SIGNAL
ACKNOW-
GENERAL
SILENCE
ALARM
LEDGE
MENU
ENTER
CANCEL
INFO
A.C.
ON
PRE-
ALARM
GROUND
FAULT
FIRE
SYSTEM
LAMP
DRILL
RESET
TEST
LT-895MP Rev. 0
March 2021
Table ofContents
Advertisem*nt
Table of Contents
Summary of Contents for MGC RAXN-4000LCD
- Page 1 RAXN-4000LCD Network Remote Annunciator Panel MGC Network MENU Fire Control System - System Normal - ENTER CANCEL Feb 21, 2018 2:21 PM INFO A.C. ALARM SUPV. TROUBLE MONITOR PRE- QUEUE QUEUE QUEUE QUEUE ALARM GROUND FAULT SIGNAL ACKNOW- FIRE SYSTEM...
-
Page 3: Table Of Contents
Table of Contents Introduction Installation Instructions Jumper Settings DIP Switch Settings Wiring Instructions Cable Connections Specifications Battery Calculations Warranty and Warning Information... -
Page 4: Introduction
41 frames made up of display adder modules and up to 7 RAXN-4000LCDs per node, refer to figure below. The RAXN-4000LCD may be mounted in the BB-1000 (MMX-BB- 1000) Series backboxes, the BB-5008, BB-5014, BBX-FXMNS (MMX-BBX-FXMNS) and FX- LOC (MMX-LOC) enclosures. -
Page 5: Installation Instructions
Installation Instructions The RAXN-4000LCD chassis is mounted with four hex nuts. Figure below shows the RAXN- 4000LCD mounted into a BB-1001D/DR/DS (MMX-BB-1001D/DR) backbox. Dimensions for height and mounting hole locations change for the various backboxes as shown in the table below. -
Page 6: Jumper Settings
41 frames. LCD Display Printer Connection Contrast Adjust 24V POWER TERMINALS RS-485 TERMINALS Jumpers: JW2, JW1, JW3 MGC Network Fire Alarm Control System - System Normal - February 21, 2018 10:08 AM MONITOR TROUBLE ALARM SUPV. -
Page 7: Dip Switch Settings
DIP switches of SW1. The RAXN-4000LCD SW1 DIP switches are set by selecting the active ON. The addresses available for the RAXN-4000LCD are 33 to 39, inclusive. Set the address as follows in the table below: RAXN-4000LCD Remote Annunciator Address Setting (DIP SWITCH... -
Page 8: Wiring Instructions
ALL CIRCUITS ARE POWER LIMITED RAXN-4000LCD AND MUST USE TYPE FPL, FPLR, OR The RS-485 wiring to the FPLP POWER LIMITED CABLE RAXN-4000LCD Display Module is recommended to be twisted shielded pair as RS-485 FROM FIRE ALARM MAIN BOARD OR PREVIOUS RS-485... -
Page 9: Cable Connections
Cable Connections The RAXN-4000LCD may be utilized by itself in a remote location or within a larger enclosure together with other display modules. It may also be used as part of a mass notification system. Below is an example of a RAXN-4000LCD and a RAX-1048TZDS 48 LED Annunciator Display module in a BB-1002D/DR/DS (MMX-BB-1002D/DR) enclosure. -
Page 10: Specifications
Standby: 139 mA Max., All LEDs ON: 164 mA Max. RAX-1048TZDS Adder Annunciator Module (48 Display Points) • Interconnects via one ribbon cable from RAXN-4000LCD or to previous RAX-1048TZDS or IPS-2424DS to the next RAX-1048TZDS or IPS-2424DS. • Annunciation of up to 48 additional points. -
Page 11: Battery Calculations
Battery Calculations Current Drain for Battery Calculations The following are the currents for the RAXN-4000LCD to which is added the number of RAX- 1048TZDS and/or IPS-2424DS or FDX-008W(KI) used: Normal Standby Current = 139 mA + ___________ x 22 mA + ___________ x 10mA = _______... -
Page 12: Warranty And Warning Information
Warranty and Warning Information WARNING! Please read this document CAREFULLY, as it contains important warnings, life-safety, and practical information about all products manufactured by the Mircom Group of Companies, including Mircom and Secutron branded products, which shall include without limitation all fire alarm, nurse call, building automation and access control and card access products (hereinafter individually or collectively, as applicable, referred to as “Mircom System”). - Page 13 The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of the system. NOTE TO USERS: All Mircom Systems have been carefully designed to be as effective as possible. However, there are circ*mstances where they may not provide protection.
- Page 14 13. Wireless Devices Placement Proximity. Moreover all wireless devices must be a minimum and maximum distance away from large metal objects, such as refrigerators. You are required to consult the specific Mircom System manual and application guide for any maximum distances required between devices and suggested placement of wireless devices for optimal functioning.
- Page 16 CANADA - Main Office U.S.A © Mircom 2021 25 Interchange Way 4575 Witmer Industrial Estates Printed in Canada Subject to change without prior notice Vaughan, ON L4K 5W3 Niagara Falls, NY 14305 Tel: (905) 660-4655 Tel: (905) 660-4655 www.mircom.com (888) 660-4655 (888) 660-4655 Fax: (905) 660-4113 Fax: (905) 660-4113...
